TOPIC: DIY PMMA injections

As per title. Is it possible to conduct the process of injecting PMMA into your member if you had all the correct ancillaries and a sound knowledge of the process?

I guess this would not be for the faint hearted. Also extreme discipline of hygene would be required.

I am not planning on doing this. Only opening the topic up for discussion.

It would be good to hear from those who have had the operation, was it complicated?

Cheers

Possessing knowledge of the technique(s) is not the same as possessing the s. It seems to be common acceptance (at least as far as this forum is concerned) that the s of the practitioner plays a significant role in the outcome of a penile bioplasty procedure.

The procedure can take as long as an hour, it\'s not one of those \"stick it in, and start squirting away\" kind of 15-minute operations.

I personally think a Do-It-Yourself with any cosmetic procedure as an untrained, unlicensed, and unqualified individual is the silliest kind of dumb.

And imagine thinking you can handle the mental strain only to faint with needles Hanging off your Dick?

Yes I have to agree, the thought of perfroming the op yourself is not for me either, but the question remains - is it possible.

There is a blog where the author has spent years experimenting injecting various different concoctions into his member and writing about the results. So, there are obviously people out there who dont \"faint with needles Hanging off their Dick\".

Also, when PMMA penis injections were first performed by practioners, the practioners were in virgin teritory, they hadn\'t performed this before, yet they were successful.

I am not 100% sure on the op (because I haven\'t experienced it -though I have read most of the personal experinces on this board), in theory it doesn\'t seem an overly complicated procedure. I imagine there are minor technicalities, such as avoiding injecting into the blood stream, rupturing blood vessels, internal bleeding, alergic reaction etc etc etc

Could someone with local pain ers and the correct surgical apparatus perform this on them selves???

The idea is making me wince just thinking about it

si_mon wrote: Yes I have to agree, the thought of perfroming the op yourself is not for me either, but the question remains - is it possible.

There is a blog where the author has spent years experimenting injecting various different concoctions into his member and writing about the results. So, there are obviously people out there who dont \"faint with needles Hanging off their Dick\".

Also, when PMMA penis injections were first performed by practioners, the practioners were in virgin teritory, they hadn\'t performed this before, yet they were successful.

I am not 100% sure on the op (because I haven\'t experienced it -though I have read most of the personal experinces on this board), in theory it doesn\'t seem an overly complicated procedure. I imagine there are minor technicalities, such as avoiding injecting into the blood stream, rupturing blood vessels, internal bleeding, alergic reaction etc etc etc

Could someone with local pain ers and the correct surgical apparatus perform this on them selves???

The idea is making me wince just thinking about it

I think I know which blog you are talking about - and if I\'m not mistaken, its primarily focused around Chemical PE. That\'s a lot different than what\'s going on with penile bioplasty. To be honest, I\'ve never wanted to watch any of my procedures, but from all the commotion I can see going on, I don\'t believe it is as simple as merely injecting some syringes into the penis. It would be nice for anyone who has directly observed this procedure to chime in, but just because it \"seems\" easier than, say, full-blown surgery, it doesn\'t mean that it is. Besides, the penis is a dynamic organ and will require a lot of craftsmanship to get a desirable end result.

You could always ask the doctors who perform this in their practice themselves. They may be able to say whether or not it can be done as a DYI (though they obviously wont recommend it).

If it is just a matter of \"can it be done at all,\" then I suppose it\'s possible, but not without a lot of risk. Humans are remarkable creatures, versatile and crafty. I\'m sure with the right knowledge & preparation, someone could give themselves this procedure but it would be on a much more intense level of self-administration than any of the Chemical PE that blog guy does.

And as I\'ve said before, it would be the silliest kind of dumb when the procedure is being offered on 3 different continents by those who are actually sed in the art of bioplasty.

si_mon wrote: Yes I have to agree, the thought of perfroming the op yourself is not for me either, but the question remains - is it possible.

There is a blog where the author has spent years experimenting injecting various different concoctions into his member and writing about the results. So, there are obviously people out there who dont \"faint with needles Hanging off their Dick\".

Also, when PMMA penis injections were first performed by practioners, the practioners were in virgin teritory, they hadn\'t performed this before, yet they were successful.

I am not 100% sure on the op (because I haven\'t experienced it -though I have read most of the personal experinces on this board), in theory it doesn\'t seem an overly complicated procedure. I imagine there are minor technicalities, such as avoiding injecting into the blood stream, rupturing blood vessels, internal bleeding, alergic reaction etc etc etc

Could someone with local pain ers and the correct surgical apparatus perform this on them selves???

The idea is making me wince just thinking about it

Could you link that blog please? thanks

yeah sure, its

www.chempe.com

Is that it then? No one can add anything to the discussion?! Dissapointing

si_mon wrote: yeah sure, its

www.chempe.com

Is that it then? No one can add anything to the discussion?! Dissapointing

The database forums are less visible, I\'ll move this to the General Discussion Forum to see if anyone else wants to chime in.

ok great. I might and try and contact the bloke off that blog to see if he has considered PMMA